M-35E 1HP 3PHASE 208/230/480VAC SLIDE GATE OPERATOR
MODEL M-35 Slide Gate Operator 1 HP. Each machine is a complete package with a heavy-duty clutch, operator stand, 27 feet of chain, 2 mounting brackets, factory tested and installed electrical circuitry, and EMDL (Electromagnetic Drive Lock). 1HP, job specific 3 PH 208/230/480VAC
TECHNICAL SPECIFICATIONS FORCUSTOMLINE M-35 SERIES
SLIDE GATE OPERATORS 1 H.P. – THREE PHASE
MOTOR REDUCER: 1 HP Input 1800 RPM to 58 RPM. Single
right angle worm gear reducer rated at 2HP. Torque rating 804
inch pounds with 30:1 ratio.
BEARINGS: All bearings to have basic static load rating of
3870 lbs and a basic dynamic load rating of 3870 lbs. Seals to be
rated at 8700 RPM.
CHAIN DRIVE: Factory plated #50 roller chain rated at 6100
lbs average tensile strength. Chain adjustment screws shall be
5/8” diameter with minimum of 3-1/4 threads. Chain mounting
bracket shall be 5/8” x 2” x 7” steel bar drilled for adjustment
screws.
SPROCKETS: All are made of high carbon steel
CLUTCH: To be self-contained over-center type easily
adjusted. Rated at 1.7 HP per
100 RPM with 1080-inch lbs of torque capacity.
CONTROL CIRCUITRY: Factory installed, complete with
thermal overload protection, reversing contactors with built-in
mechanical and electrical interlock to prevent double closure.
Heavy-duty silver-to-silver contacts rated at 5 HP. Control
transformer to be heavy duty with .250 KVA rating.
OPERATOR: To be built on heavy-duty 3/8” structural steel
frame. All shafting 1 3/8” throughout.
HOUSING: 1/8” Aluminum.
STAND: 8” x 8” x 3/16” steel tube with 3/8” steel top and
bottom plate.
GATE SPEED: Standard- approximately 60 FPM.
LIMIT SWITCH: Rotating direct chain drive controlled by
output shaft. Micro switch and cam action allowing close
tolerance open and close adjustment.
DRIVE LOCK: Varnum slide gate operators to be locked in
position by means of an electromagnetic brake located on the
main drive shaft. Locking brake has a static torque rating of
684-inch lbs and is equipped with a positive release to
eliminate friction drag during the drive mode. Epoxy resin
bonding of the brake friction lining, coil, and terminals provide
construction strength, electrical and environmental insulation
and heat dissipation for longer service life. Failsafe design
allows lock release in case of power failure. Maximum power
consumption 36 watts.
CLOSING UNIT: Industrial series panel mount automatic reset
timer commonly used in applications requiring high repetitive
accuracy, fast reset and heavy usage. It is equipped with
10AMP, single throw, double throw, isolated load contacts for
gate control.
MODEL M-35 Slide Gate Operator 1 HP. Each machine is a complete package with a heavy-duty clutch, operator stand, 27 feet of chain, 2 mounting brackets, factory tested and installed electrical circuitry, and EMDL (Electromagnetic Drive Lock). 1HP, job specific 3 PH 208/230/480VAC
TECHNICAL SPECIFICATIONS FORCUSTOMLINE M-35 SERIES
SLIDE GATE OPERATORS 1 H.P. – THREE PHASE
MOTOR REDUCER: 1 HP Input 1800 RPM to 58 RPM. Single
right angle worm gear reducer rated at 2HP. Torque rating 804
inch pounds with 30:1 ratio.
BEARINGS: All bearings to have basic static load rating of
3870 lbs and a basic dynamic load rating of 3870 lbs. Seals to be
rated at 8700 RPM.
CHAIN DRIVE: Factory plated #50 roller chain rated at 6100
lbs average tensile strength. Chain adjustment screws shall be
5/8” diameter with minimum of 3-1/4 threads. Chain mounting
bracket shall be 5/8” x 2” x 7” steel bar drilled for adjustment
screws.
SPROCKETS: All are made of high carbon steel
CLUTCH: To be self-contained over-center type easily
adjusted. Rated at 1.7 HP per
100 RPM with 1080-inch lbs of torque capacity.
CONTROL CIRCUITRY: Factory installed, complete with
thermal overload protection, reversing contactors with built-in
mechanical and electrical interlock to prevent double closure.
Heavy-duty silver-to-silver contacts rated at 5 HP. Control
transformer to be heavy duty with .250 KVA rating.
OPERATOR: To be built on heavy-duty 3/8” structural steel
frame. All shafting 1 3/8” throughout.
HOUSING: 1/8” Aluminum.
STAND: 8” x 8” x 3/16” steel tube with 3/8” steel top and
bottom plate.
GATE SPEED: Standard- approximately 60 FPM.
LIMIT SWITCH: Rotating direct chain drive controlled by
output shaft. Micro switch and cam action allowing close
tolerance open and close adjustment.
DRIVE LOCK: Varnum slide gate operators to be locked in
position by means of an electromagnetic brake located on the
main drive shaft. Locking brake has a static torque rating of
684-inch lbs and is equipped with a positive release to
eliminate friction drag during the drive mode. Epoxy resin
bonding of the brake friction lining, coil, and terminals provide
construction strength, electrical and environmental insulation
and heat dissipation for longer service life. Failsafe design
allows lock release in case of power failure. Maximum power
consumption 36 watts.
CLOSING UNIT: Industrial series panel mount automatic reset
timer commonly used in applications requiring high repetitive
accuracy, fast reset and heavy usage. It is equipped with
10AMP, single throw, double throw, isolated load contacts for
gate control.
MODEL M-35 Slide Gate Operator 1 HP. Each machine is a complete package with a heavy-duty clutch, operator stand, 27 feet of chain, 2 mounting brackets, factory tested and installed electrical circuitry, and EMDL (Electromagnetic Drive Lock). 1HP, job specific 3 PH 208/230/480VAC
TECHNICAL SPECIFICATIONS FORCUSTOMLINE M-35 SERIES
SLIDE GATE OPERATORS 1 H.P. – THREE PHASE
MOTOR REDUCER: 1 HP Input 1800 RPM to 58 RPM. Single
right angle worm gear reducer rated at 2HP. Torque rating 804
inch pounds with 30:1 ratio.
BEARINGS: All bearings to have basic static load rating of
3870 lbs and a basic dynamic load rating of 3870 lbs. Seals to be
rated at 8700 RPM.
CHAIN DRIVE: Factory plated #50 roller chain rated at 6100
lbs average tensile strength. Chain adjustment screws shall be
5/8” diameter with minimum of 3-1/4 threads. Chain mounting
bracket shall be 5/8” x 2” x 7” steel bar drilled for adjustment
screws.
SPROCKETS: All are made of high carbon steel
CLUTCH: To be self-contained over-center type easily
adjusted. Rated at 1.7 HP per
100 RPM with 1080-inch lbs of torque capacity.
CONTROL CIRCUITRY: Factory installed, complete with
thermal overload protection, reversing contactors with built-in
mechanical and electrical interlock to prevent double closure.
Heavy-duty silver-to-silver contacts rated at 5 HP. Control
transformer to be heavy duty with .250 KVA rating.
OPERATOR: To be built on heavy-duty 3/8” structural steel
frame. All shafting 1 3/8” throughout.
HOUSING: 1/8” Aluminum.
STAND: 8” x 8” x 3/16” steel tube with 3/8” steel top and
bottom plate.
GATE SPEED: Standard- approximately 60 FPM.
LIMIT SWITCH: Rotating direct chain drive controlled by
output shaft. Micro switch and cam action allowing close
tolerance open and close adjustment.
DRIVE LOCK: Varnum slide gate operators to be locked in
position by means of an electromagnetic brake located on the
main drive shaft. Locking brake has a static torque rating of
684-inch lbs and is equipped with a positive release to
eliminate friction drag during the drive mode. Epoxy resin
bonding of the brake friction lining, coil, and terminals provide
construction strength, electrical and environmental insulation
and heat dissipation for longer service life. Failsafe design
allows lock release in case of power failure. Maximum power
consumption 36 watts.
CLOSING UNIT: Industrial series panel mount automatic reset
timer commonly used in applications requiring high repetitive
accuracy, fast reset and heavy usage. It is equipped with
10AMP, single throw, double throw, isolated load contacts for
gate control.